fbpx
FREE shipping on orders over $75. Shop now!
×
Save Time and Money with Our FREE Hot Tub Cheat Sheet
Download this FREE printable cheat sheet to keep your hot tub clean and clear. You’ll never worry about your hot tub again with this easy-to-use guide.

How to Start a Hot Tub in 12 Easy Steps

Matt Giovanisci, Founder and CEO of Swim University By Matt Giovanisci | November 2, 2020

Whether you have a brand new hot tub or you haven’t used it in a couple of months, making sure the water is safe and clean is paramount to enjoying a long soak. If it’s your first time starting a hot tub, you might feel a little overwhelmed. If you slacked a little on your spa maintenance, you might be struggling to remember everything you need to do.

Don’t worry, we’ve got your back. Follow these 12 simple steps to start a hot tub like a pro.

The Hot Tub Care Video Course
Tired of wasting time, money, and chemicals trying to keep your hot tub clean?

Cut the confusion with our easy-to-use video course. Save $1,000's on hot tub care and keep your water clean and clear for good!

Learn More

1. Rinse and Drain

If you’re a new hot tub owner, you’re going to have to get used to the cleaning that comes with hot tub ownership. If you’re a more seasoned owner, you know the drill.

For New Hot Tubs

Many manufacturers ship hot tubs with a small amount of antifreeze just in case they’re exposed to freezing temperatures on the way to your house. It protects the plumbing from any potential damage, but it’s not something you want to soak in.

Fill the tub’s footwell—that’s the bottom portion where you place your feet—with water, run the pumps for a few minutes, and then drain. This clears any antifreeze out of your plumbing system.

To Restart a Hot Tub

If you’ve left your water sitting for a long period of time with no maintenance, you need to drain and clean your hot tub to get rid of the old water and any bacteria colonies that could make you sick.

After draining, refill the tub with new water. Choose a good jet and drain cleaner, and follow the instructions on the package. Allow the jets to run long enough to do a thorough cleaning job.

Our Top Pick
Hot Tub Detox: Line Flush & Plumbing Purge

Don't let your hot tub fill with hard-to-remove gunk. Clear out the gunk and keep your hot tub water fresh. It removes gunk in your pipes caused by lotions, sunscreens, cosmetics, etc.

Buy Now From Swim University

Once your jets and drains are clean, drain the hot tub again.

Tip: If you winterized your hot tub, your drain plugs and fittings will have been left unscrewed or open. Before filling your tub with water, remember to make sure everything is reconnected:

2. Turn off All Power

We’re big on safety here. Before you do any major cleaning you should always disconnect all power to your hot tub to prevent any shocking mistakes.

This doesn’t mean simply flipping your spa equipment switch. Unplug your tub and turn off the circuit breaker to ensure the power is completely cut off. Remember, water and electricity to not mix.

3. Clean the Empty Hot Tub

You wouldn’t bathe in a dirty tub or shower, right? Well, you don’t want to soak in a dirty hot tub either. Keeping your spa clean is pretty much a third of the maintenance along with water chemistry and hardware upkeep.

For New Hot Tubs

When you first start a spa, you want to make sure all the surfaces that water may come into contact with are as clean as possible. Spray and wipe down the shell (that’s the actual tub of your hot tub) and the cover.

Use a non-abrasive cleaner and a soft cloth or sponge to prevent any damage to your shell. Rinse thoroughly to keep your hot tub from foaming later.

To Restart a Hot Tub

If your spa sat with stagnant water in it for a while, it’s a good idea to perform a hot tub deep clean to get it back to usable status.

Our Top Pick
Hot Tub Weekly Cleanse: Water Conditioner & Clarifier

Our once-a-week treatment combines hot tub cleaner, conditioner, and water clarifier to give your hot tub water a soft & silky feel. Plus sparkling clean water!

Buy Now From Swim University

4. Install or Clean the Filter

Your hot tub filter plays a crucial role in maintaining the cleanliness of your water. This is the best time to install new filters or clean your old filters.

For New Hot Tubs

Install a filter cartridge into every filter well. Some hot tubs only have one, but check your owner’s manual just to be safe.

To Restart a Hot Tub

Remove and inspect any filter cartridges currently installed. Check them all to see if they need to be replaced.

If they’re just dirty, you can clean the hot tub filters by spraying them down with filter cleaner. If they’re extremely dirty, put them in a chemical soak overnight. Actually, it doesn’t matter if they look dirty or not, it’s safer to clean them anyway.

Once the filter cartridges are clean, inspect them one more time in case they need replacing before reinstalling them into your filter wells.

Our Top Pick
Hot Tub Filter Cleanse: Deep-Cleaning Soak

Soak your hot tub filters in our deep-cleaning Filter Cleanse solution, rinse with water, and your filters will look brand new in 24 hours!

Buy Now From Swim University

5. Fill Your Hot Tub

Whether you’re filling your hot tub for your first or fiftieth time, we also recommend you use a hose filter. It will help remove any impurities from your water source, including high mineral levels (which can clog your system), metals like copper and iron (which can turn your water green or brown), and calcium (which can cause buildup in your shell and plumbing).

Hose filters prevent mineral and metal problems before they start, which can save you a lot of time and money.

Even with a hose filter, we recommend placing the hose into the filter well. This lets the water circulate through the system and push out any air locks (air stuck in the plumbing).

Our Top Pick
Hose Filter with Flexible Hose Protector

Fill your pool or hot tub with this hose filter that'll filter your water so you can have a fresh start with water chemistry.

Buy Now On Amazon
If you click this link and make a purchase, we earn a commission at no additional cost to you.

Using the Filter Well

If you don’t have a hose filter, the next best thing is to place the hose directly into the filter area rather than the footwell. You’ll get the filtering benefits from the hot tub’s filter, and will still head off any air lock problems.

Monitor the Water Fill Level

Your owner’s manual may have specific instructions on how high your water level should be, but generally, you want the water level to be about an inch below the headrests while still being high enough to fully cover the jets.

Try to resist the temptation to add a little more water. When you, your family, or your guests enjoy the tub, the water level rises. If you spill water, it can throw off the balance of your hot tub chemistry, which means more work for you later. Plus, if your hot tub is indoors, you’ll have a slippery mess.

You also want to make sure your water level is high enough. Low water levels can cause your heater and pump shut down, which means no outflow from the jets and less filtration. Plus, if you live in a colder climate, your water might not circulate properly and your pipes could freeze.

6. Prime the Pump

Air in your hot tub’s lines can cause a whole slew of problems. To make sure air is out of everything, you need to prime the hot tub pump. This process varies depending on the manufacturer and model, so consult your owner’s manual before proceeding.

Some control panels have a self-priming mode. If yours doesn’t, you’ll have to prime it manually using a bleeder valve.

Control Panel Priming

It’s easy to prime your pumps using your control panel, if it has the setting:

  1. Press the jets button to turn the pump on. Run for ten to twenty seconds.
  2. Press the jets button again to turn the jets on high. Run for another ten seconds, and make sure all the jets are working.
  3. Turn off the jets by pressing the jets button again.
  4. Continue to repeat this process until water circulates through all the jets. You’ll know the pump is primed if all the jets are working as they should.

Bleeder Valve Priming

It’s not a big deal if your hot tub doesn’t have a self-priming mode. It’s just as easy to prime your hot tub using a bleeder valve, which is a nozzle on the pump that allows air to escape:

  1. Make sure all power is disconnected from your hot tub by turning off your spa and the breaker.
  2. Locate your hot tub’s pump. If you’re unsure of its location, check your owner’s manual.
  3. Close the gate valve on the discharge side of the pump. This shuts off the water flow.
  4. Turn the bleeder valve counterclockwise until you hear it start to hiss. That’s air leaving the pump. All the air has been released when the hissing stops.
  5. Once all the air has escaped, tighten the bleeder valve, reopen the gate valve, and turn the hot tub power on.
  6. Turn on the jets to check whether the water is flowing properly. Repeat the process until the pump is primed and water is flowing normally.

Help! My Water Isn’t Flowing

If your jets are running and there’s no water flowing through them, you’re probably experiencing an air lock. They’re not uncommon and they’re simple to fix, so don’t worry. To get rid of an air lock:

  1. Turn all of your jets’ faceplates counterclockwise to open them.
  2. Keep the heater off by turning down your thermostat.
  3. Press the jets button twice to turn the jets on high. Let them run for ten to fifteen seconds. Turn off the jets.
  4. Repeat the previous step three more times, increasing the run time by ten to fifteen seconds.
  5. You will start to see air bubbles coming from the jets. Keep the jets running until all the air has been released.

7. Add the Start-Up Chemicals

Now that your filters are clean and installed, your water is fresh, and your pump is primed, it’s finally time to add your start-up chemicals. Wait until your hot tub water reaches 80ºF (30ºC) before you add anything. The heat helps the chemicals dissolve and incorporate into the water.

If you’re not sure what chemicals you need, check out our guide to Hot Tub Chemicals. And if you’ve never added chemicals to your water before, we have a few tips before you get started:

8. Run the Hot Tub

Once your chemicals are added, run your hot tub with the jets on low for at least 20 minutes. This evenly distributes the chemicals in the water. But keep your air valves off. Too much air in the water can raise your pH and over-oxidize your chemicals.

9. Test Your Water

If you’re a new hot tub owner, get ready to discover the high school chemistry throwback that is testing your hot tub water.

You may have measured the chemicals, but you should always check to make sure your chemistry is correct. If your chemistry is off, it can damage your hot tub, irritate your skin, or allow nasty bacteria to invade your relaxation time.

If you’re a new hot tub owner, and you’re not sure how to test your hot tub water, don’t worry. It’s not as difficult as it may seem, and you’ll get the hang of it in no time.

We also recommend you plan to test your hot tub water at home once a week and have your water professionally tested at your local spa supplier once a month.

10. Set the Water Temperature

Some like it hot, and some like it hotter. You should find the temperature that’s most comfortable for you, but we recommend keeping your water between 98ºF and 102ºF (36ºC and 38ºC).

Caution: Your water temperature should never, ever exceed 104ºF (40ºC). You could burn yourself or damage your hot tub, or both.

While your hot tub control panel has a thermometer, we recommend you test your water with a separate thermometer to ensure an accurate reading.

We also recommend that you keep your water’s temperature consistent. If you let your water cool off and reheat with every use, you run the risk of stressing the heater and circuit board. Not to mention, you’ll waste a ton of energy and get a higher electric or gas bill.

11. Cover Your Hot Tub

Let your water circulate for another ten minutes after you set the temperature. Cover your tub for approximately twenty-four hours. This helps the temperature rise, retain heat, and prevent loss of water and chemicals through evaporation.

Custom Hot Tub and Spa Cover Replacement

All custom spa covers are made to order with the exact measurements provided to ensure a perfect fit. They utilize the highest quality marine grade vinyl and insulation that sets their covers apart in the industry.

Buy Now On Amazon
If you click this link and make a purchase, we earn a commission at no additional cost to you.

12. Test Your Water

No, we’re not just repeating ourselves. Now that your water has had some time to stabilize, the chemical levels may not be correct. Before you use the hot tub, test the water a second time and adjust chemical levels as needed.

Additional Considerations Before Restarting Your Hot Tub

When you start a spa after a long break, inspect your hot tub for any cracks, stains, or mildew. Dampness may disguise damage, so it’s important to wait for your tub interior to dry completely before looking it over.

Be sure to also take a peek at the wiring before you refill. If you see any frayed cords or loose connections, call a qualified electrician to inspect it. Unless you’re a licensed electrician, working with electrical systems is best left to a professional.

Great Work!

You’ve successfully started or restarted your hot tub. We told you it wasn’t that complicated. As a reward, sit back, relax, and let your troubles float away in your hot tub.

Happy Soaking!

Need More Hot Tub Maintenance Help?

Matt Giovanisci, Founder and CEO of Swim University
Matt Giovanisci is the founder of Swim University® and has been in the pool and spa industry since 1993. Since then, his mission is to make pool and hot tub care easy for everyone. And each year, he continues to help more people with water chemistry, cleaning, and troubleshooting.

Featured Hot Tub Products

Save Time and Money with Our FREE Hot Tub Cheat Sheet
Download this FREE printable cheat sheet to keep your hot tub clean and clear. You’ll never worry about your hot tub again with this easy-to-use guide.